Fix Christmas Light Strings Not Working Tutorial

Home > Christmas Light > Christmas Light Strings Not Working

Christmas Light Strings Not Working


Position the two prongs of the sparker against the two prongs of the Christmas light plug. Was this answer helpful? Upon doing this, string 1 & 2 remained lit while now string 3 & 4 also lit fully. This isn't the same thing as testing for bad lights and replacing them.

I will be content that, 'it's a mystery.' 12/07/2010 by Mickey Ray Are you using the same outlet whenever you have the half-side failure? The 'electronics' are housed in a heat molded lump of plastic close to each end of the string. While you are inspecting your defunct string, break into and have a look at an LED. So 'screw it', off to the landfill they go !

How To Fix Christmas Lights That Don't Work

who knows?!? 5). The various ‘forums’ offer different methods to solve this problem, but most don’t work . The plastic that protects the led was loose. Steps Method 1 Replacing a Blown Fuse 1 Try this if the entire string goes out.

Was this answer helpful? January 9 by shashachap Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Discovered that I had current end to end on ALL my strings (except the ones the squirrels chewed the sockets off) from various stores, Costco, Home Depot, Wal-Mart, Rona, Sears, and How To Test Christmas Lights Without A Tester To remove that is to invite disaster.

Reader's Digest Taste of Home Recipes © 2016 HOME SERVICE PUBLICATIONS, INC. Cancel Drew Rep: 1 Posted: 12/10/2013 Options Permalink History You know... Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Get More Information I have 4 connected strings of 50 LED lights that have worked for the last 2 years.

The recyclers, for the responsible, are getting filled up with these strings of lights, and the Landfills for the less responsible . How To Find Broken Light In Christmas Lights Was this answer helpful? There is no heat in female #2 and I've dried drying it with no success. Alternatively, buy a cheaper light bulb tester without the other features.

How To Replace A Christmas Light Bulb

Was this answer helpful? Cancel Billy Livingston Rep: 1 Posted: 12/10/2013 Options Permalink History After reading most of the Q & A's here. How To Fix Christmas Lights That Don't Work The out-of-polarity ones will not work properly with the global-rectified strings, exhibiting the behavior already mentioned. How To Find The Bad Bulb On Christmas Lights I will not buy Noma lights again if I can find a replacement maker other then Noma . 11/23/2015 by Ron I bought 70 mini lights half my tree went out

I discovered it before I put it up on the eaves. weblink Ideally, check the packaging your lights came in to see what type of bulb is needed. lighting led 10 Questions View all bac @bac Rep: 7.8k 40 20 8 Posted: 12/06/2009 Options Permalink History Subscribe Unsubscribe Half of the string of LED Christmas lights doesn't light up. This makes it virtually impossible to get that one section of lights to work unless I decide to do the repair in the non-working environment . How To Open Fuse Box On Christmas Lights

Trouble-shooting these groupings by shorting out the connectors etc is not recommended, because those bulges on the string are configured for the number of lights in the string. If the bad light is the first one you replace, it's an easy fix. Cancel Chris Rep: 1 Posted: 12/13/2013 Options Permalink History Thanks for the feedback. navigate here Took about 12 LEDs to find the culprit with the shirt wire.

Yes No Voted Undo Score 0 Cancel Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? Light Keeper Pro Corrison starts and it's just a matter of time until the bulb and socket are shot. Cancel robert Rep: 1 Posted: 12/10/2012 Options Permalink History it was easy to replace the bulb every string comes with replacements.

Cancel RoddyMacRoddy Rep: 133 4 2 Posted: 12/12/2013 Options Permalink History Hi Chris Its behaving like strings 3 & 4 are hooked up in series to the female end of 2.

Was this answer helpful? A World War II veteran finally gets a long overdue reward.Crews battle brush fire in Linda VistaCrews battle brush fire in Linda VistaUpdated: Saturday, November 12 2016 9:38 PM EST2016-11-13 02:38:27 LED #7 proved to be the problem. Half Of Christmas Lights Don't Work The whole string used to work, and it's only about a year or two old.

Except I started at the plug-end and it was third from last at the opposite end. Check on here Yes, I made it! his comment is here If there was a problem with one of those sub-sets, just that set would not light.

Next I make sure each bulb in the strand is tightly in it's socket, and I try to hold them up to a light to try to see if any look Cancel doylesee Rep: 1 Posted: 11/30/2013 Options Permalink History i checked each led bulb by pulling it out and looking at the two wires. Cancel chris Rep: 1 Posted: 11/10/2012 Options Permalink History Ok, so I am having the same problem. This will make the lights unnoticeably dimmer.

Each Christmas light bulb has a "shunt" that is supposed to close the gap when the bulb burns out. Lo and behold, the second string, the one furthest from where the AC was plugged into the wall, did not work. the answer ended up being very annoying and simple. If you're looking for quick results, try the methods above instead. 2 Find a lighter operated by button.

Cancel Jim S Rep: 1 Posted: 04/03/2014 Options Permalink History I have a variation on the above problem - I have a (quite) new 200 string LED set, the first 40 I put my tree up today and added extra lights. I am not sure where you are located but I get my replacement fuses at Walmart and its a lot cheaper and less time consuming to start with that.