How To Repair Christmas Lights Plug Not Working (Solved)

Home > Christmas Light > Christmas Lights Plug Not Working

Christmas Lights Plug Not Working


Cancel loadster Rep: 1 Posted: 12/09/2013 Options Permalink History I started down this path because I have a no-name LED set with 50 lights and they all checked good with legacy Many Christmas lights are sold with spare fuses for this purpose. There must be a fault in the 2nd half of the string, or the fuse in that half must have blown. My daughter bought a couple sets at another store and only half of each string lit up.

I listened to all the answers and none actually solved the problem. But I think chances are you have one failed LED. Once you’re replaced the fuses, test out your Christmas lights to see if they work. Here's a list.

How To Fix Christmas Lights Half Out

Pull all the light bulbs out and test them, it is highly unlikely that there will be a problem with the strings itself.lemonie6 years agoReplyIf these are strung in series (as The various ‘forums’ offer different methods to solve this problem, but most don’t work . Turn on the switch to see if the lights light up. 2 Find the male sockets. Different length strings bulbs all have different 'power needs' to light 'em up. 6.

Gather all the light strands that are not working. If you have a string failure, best to cut your losses and go get yourself a new one. But ONE of the lights which wouldn't work was "so dead" that even the other lights wouldn't work. Light Keeper Pro how many strings they've thrown away and re-bought, to say nothing of the recyclable glass, copper, and plastic in this 'offshore' junk.

Cancel 11team Rep: 603 13 6 Posted: 12/06/2009 Options Permalink History half a string is better than no string, cutting the 'broken half' off makes sense - as long as the Your Name: Your Message: Send me a copy Send cancel Please wait... Do not use the type with a metal wheel, which creates the spark through friction. 3 Empty the lighter of fuel. More hints Sometimes things are more complicated: Incandescent light bulbs are most likely to fail at the instant they are turned on.

The fuse is actually a 1.2 ohm 1/4 watt resistor and in the set I hacked is present at each end. How To Test Christmas Lights Without A Tester Write an Article 152 MESSAGES LOG IN Log in via Log In Remember me Forgot password? You may have to do this with every last lamp in the bad section! Cancel Mik Mul Rep: 1 Posted: 10/12/2015 Options Permalink History Hello, i just found this thread.

How To Replace Christmas Light Bulb

Published on Dec 16, 2012HOW TO FIX OR REPAIR CHRISTMAS LIGHT IN 2 MINUTES WITHOUT NO TOOLS:1- CHECK IF THERE IS A BULB MISSING2- IF YOU DON'T HAVE A REPLACEMENT BULB, Any ideas before I head out to Canadian Tire? How To Fix Christmas Lights Half Out Just added an image to my original answer so you can see what I am referring to. 11/01/2011 by oldturkey03 Add a comment 0/1024 Cancel Post comment Are you sure you How To Find The Bad Bulb On Christmas Lights It is true these LED strings aren't as perfect as we'd been led to believe, but many of the issues can be resolved.

Help please Daria Humphrey - 11/30/2015 Reply Christmas lights are the most frustrating thing in the world...if they don't work...don't waste your time, just go get new lights! weblink The string I took apart had failed and the cause was dry solder joints at the diodes. That often works even when several lights have failed. Press the button (or pull the trigger, depending on the model) about 20 times.[4] You should hear a click each time. How To Open Fuse Box On Christmas Lights

I encountered the age-old problem of half the strand not working. Then, when we plug a new bulb in, power goes on, and weak bulbs can go out at that time. Method 4 Replacing Individual Bulbs 1 Twist the light bulb to check the connection. navigate here Home About wikiHow Jobs Terms of Use RSS Site map Log In Mobile view All text shared under a Creative Commons License.

Before discarding a damaged string, remove working bulbs to use as spares. How To Find Broken Light In Christmas Lights their current draw is balance for that many lights. 12/01/2014 by RoddyMacRoddy Add a comment 0/1024 Cancel Post comment Are you sure you want to delete this zzzzzz? When you buy new LED strings pull each LED out and coat the contacts in each socket with the dielectric grease before you place the string into service.

If the string of lights still won't light up, move on to the detector.

Make sure the two copper wires are completely aligned with the holes in the bulb's base. A normal string has two such circuits. I recently bought three sets of NOMA Leds and after succesfully testing them ok, spent nearly four hours installing arounf the roof of my house. Parallel Christmas Lights Or are there several burnouts?Advertisement - Continue Reading Below Regardless, don't give up.

Make sure both fuses are secure before closing the plug door. i have C7 diamond cut and they don't seem to have prongs. 12/02/2015 by Phyllis Kandul Thanks Granpa. You should find two of them in there. Sign in to add this video to a playlist.

Simply plug in the strand, remove a bulb that's in or near the darkened section, and insert the tool into the bulb's socket. Try a paper clip etc. Cancel nick Rep: 1 Posted: 11/30/2011 Options Permalink History hmm..same problem. Powered by Mediawiki.

Then one can follow that hum from the plug, into and out of each successive light socket, until at some place the hum fails. Alternatively, buy a cheaper light bulb tester without the other features. The rest of the task is a breeze, but removing the old fuses is hard and I am having no success getting the new ones in! Don’t force them in.

If the fuse is good, you should see an unbroken strand of wire running between the two metal contacts. If you prefer to avoid buying such a specialized device, try the following alternatives: Get a non contact voltage detector and skip down to tracing the dead bulb. Yes No Voted Undo Score 20 Cancel Comments: + That just shows that when the going gets tough, the tough keep on trucking.....:-) Happy Holidays 11/26/2011 by oldturkey03 Thanks! The device I got a decade or so ago was helpful, but also relatively insensitive and tricky to use.

Was this answer helpful? CONNECT END TO END A MAXIMUM OF THREE (3) LIGHTING STRINGS OR DECORATIVE OUTFITS OF THE SAME TYPE," and that is the answer. 100-bulb light strings typically use "3A" fuses. With one string, exactly half of the LEDs don't light up when plugged into the AC. Cancel alicegwyn Rep: 1 Posted: 11/01/2011 Options Permalink History How do you open and check the fuses?

If the bulb moved noticeably, plug in the lights and see if a loose connection was causing the issue. This issue came about because around 2007~maybe 2008 one brand of string available at The Home Depot, ACE Hardware and possibly others contained a bridge rectifier (four extra, non- light emitting Repairing these lights won't be easy, but with a little determination and know-how, it can be done. Since 3 amps at 120V is 360 watts of power, it might seem that the AC outlet could support a lot of light strings, but that is deceptive.

If the fuse is obviously dark to your eye, then the fuse is burnt and will no longer work.